Water level sensor with NO and NC relay output, 10 to 15 VDC

Wire it into the pump circuit and it stops the flow when the tank reaches the sensor.

Standard shipping to Columbus: 2–4 daysStandard shipping to Columbus: 2–4 daysProcessing 2–5 business days. Tracked to your door.
Water level sensor with NO and NC relay output, 10 to 15 VDC$35.99
Tracked shippingIncluded
Taxes & import dutiesMay apply at your door
You pay$35.99
or
Questions? Email help@viversio.com. We reply within 1 working day.
Tracked to your door. Processing 2–5 business days, then standard shipping.
Covered if it's faulty Repair, replacement or refund. Change-of-mind returns only where the law gives that right. Your legal rights always apply.
Secure checkout by Stripe. We never see your card details.

What it does

This water level sensor stops your pump when the tank fills to the level you set. It ends the walk out to the tank to check, and the water spilling over the top while the pump runs on. When the water reaches the sensor, the relay acts and the circuit can stop the pump or start one, depending on the contact you wire. The sensor side runs on 10 to 15 VDC and the relay handles 250 V 10 A AC.

This water level sensor is a wired relay switch for tanks, ponds and pumps. Water towers, water heaters, fish tanks and fish ponds are the listed use occasions. When the water reaches the sensor, the relay acts and the pump stops, or starts, depending on which contact you use. The relay handles 250 V 10 A AC or 30 V 10 A DC, so it can drive a pump circuit within those limits.

Set-up is wiring work. Power the sensor side with 10 to 15 VDC at under 100 mA, place the sensor at the water line, and run the normally open or normally closed contact into the circuit you want to control. The sensor is separated from the controller, so the wet part and the electronics stay apart, which suits tanks and ponds where the level has to be held by the equipment rather than by eye.

As a liquid level sensor it fits homes, garages, warehouses, archives and machine rooms where water has to be kept at a level, and it can control high-current equipment within the relay rating. It is a switch, not a gauge: it changes state when the water reaches the sensor. If you want a number to look at from across the room, this is not the device for that job. It comes in white.

Every order is tracked to your door. Orders are processed in 2–5 business days, and the standard shipping time for your country is shown next to the price.

  • The pump stops when the tank is fullWhen the water rises to the sensor, the relay acts and your pump circuit cuts out, so the tank fills itself and stops at the level you chose. That ends the overflow on the floor and the dry-running you get when the level is never checked. The sensor side needs 10 to 15 VDC and draws under 100 mA.
  • It switches the pump you already runThe relay contacts are rated 250 V 10 A AC or 30 V 10 A DC, and loads below that range can be used. That covers the pumping pumps this sensor is listed for, along with equipment in base stations, machine rooms, garages and warehouses. Check your pump's current draw against 10 A before you wire it in.
  • Wire it to stop at the top or start at the bottomThe output is a normally open and a normally closed signal. When the relay acts, the normally open contact becomes closed and the normally closed contact becomes open. So one water level detector can cut a pump when the tank is full, or start a pump when the level drops, whichever your setup calls for.
  • The wet end and the electronics stay apartThe sensor is separated from the controller, so the part at the water line is not sitting with the electronics. That separation is paired with anti-jamming and a rapid response, which matters when a wave or a ripple crosses the sensor. Put the sensor at the level you care about and keep the controller where it stays dry.

Specs

Working voltage10 to 15 VDC
Working current<100 mA
Relay load250 V 10 A AC or 30 V 10 A DC (lower loads can be used)
OutputNormally open and normally closed signal
ConstructionSensor separated from the controller
ColorWhite

Delivery to Columbus

Every step is tracked. The tracking link comes by email, in your language.

  1. Order placedYou get a confirmation straight away.
  2. Processed and handed to the courierTracking number sent to you.
  3. Flies to United StatesThe courier may collect import duties or taxes on delivery.
  4. At your doorEstimated from recent deliveries to your country.

Returns

The short version. The returns page has the full rules.

Covered if it's faultyDamaged, wrong or not as described: tell us within 14 days of delivery. A fault in normal use: within 30 days. Email us a photo or video and we repair, replace or refund. If we need it back, we pay the postage and inspect it first.
Your legal right to withdrawIn the EU, the UK and some other countries you can also cancel within 14 days of delivery for any reason. That's your legal right. You pay the return postage.

Questions

Will it work with the tank or pond I have?

Yes, within the listed uses: water towers, water heaters, fish tanks, fish ponds and pumping pumps. As a water tank level sensor it sits at the water line you choose, and the relay acts when the water reaches the sensor. The sensor goes at the level and the controller stays out of the water.

What does it need to run?

A 10 to 15 VDC supply on the sensor side. The working current is under 100 mA. That low-voltage DC source is what drives the relay, so the unit needs a wired supply rather than batteries.

Can it switch my pump directly?

Yes, if the pump stays within the relay rating: 250 V 10 A AC or 30 V 10 A DC. Loads lower than that can be used too. Check your pump's current draw against 10 A before wiring the contact into its circuit.

How does it signal that the water reached the level?

The relay acts and the contacts change state: the normally open contact becomes closed and the normally closed contact becomes open. Wire the contact that suits your circuit, so the same sensor can stop a pump at the top of the tank or start one when the level falls.

Is it hard to set up?

It is wiring work. Give the sensor side 10 to 15 VDC, place the sensor at the water line, and run one of the two contacts into the circuit that runs your pump. Because the sensor is separated from the controller, the wet part and the electronics are handled apart from each other.

How long does shipping take?

Orders are processed in 2–5 business days. Standard shipping to United States then takes 2–4 days, and every step is tracked.

Will I pay anything when it arrives?

Possibly. Import duties and taxes for United States aren't prepaid yet, so the courier may collect them on delivery. Nothing is added to our price at checkout.

Who is Viversio?

Viversio is a brand of Ravinaro LLC, a company registered in the United States. We choose every device for what it does, and a real person answers every email.